Contact Us

Foshan Kezun Stage Lighting Equipment Co., Ltd.

Tel:  +86 757-85623159

Fax: +86 757-85623160

Add: China (Mainland) Guangdong Foshan No. 26, Caochang Hainanzhou Industrial Zone, Lishui Town, Nanhai Dist.China

Web: www.kz-lighting.com

Email: kezun05@kzlight.com

Tech Support 24 Hour Hot line:+86 4008-377-008
Home > Exhibition > Content
Moving head lights common several failures and their own solution Oct 25, 2017

To tell you about the stage moving head lights in the process of several common faults, these failures are very simple, as long as your own good investigation, and then you can solve their own. Do not have to find manufacturers to solve, today we shake the head of several common faults to do a summary, we hope to help.

 

First: shaking head light the whole lamp does not power?

1: first check the power cord is a problem;

2: check the power supply socket fuse is burned;

3: open the lamp at the end of the panel, check the ballast is powered; internal switch cable is falling like;

4: open the lamp body two shell, near the location of the bulb to check whether the temperature control failure.

 

Second: shaking his head light bulb does not shine?

1: open the light body tail check the light bulb is white or black, if there are more than two phenomena appear first to replace the light bulb and try again;

2: open the lamp body two shells, lamp posts installed on the trigger, check the trigger wiring is burning black, if there is to replace the trigger.

 

Third: shaking his head light bulb when not bright?

1: Check whether the light bulb or black or even up, when the above situation, please immediately replace the lamp, so as to avoid damage to the product;

2: Check the fan on both sides of the bulb is working properly, if there is bad, please replace the fan;

3: Please open two shells, in the pattern and the color of the layer that there is a white temperature control to see if it burned (if it will not destroy the bubble);

4: open the lamp body two shells, in the bulb on the tail of the cooling window, after a long time will plug the airway out of the way, if the dust window full of dust, please clean (this cooling window is best every month clean One effect best).

 

Fourth: moving head light bulb blown out what is the reason?

1: first check whether the voltage between 220V-230V, if more than 230V can blow the possibility of the bubble (so that the premises should be installed regulator);

2: If there is a bubble, please check whether the bubble is due to the long working life caused by (usually the normal life of domestic light bulbs in 300-500 hours);

3: Is there a problem with the quality of the lamp?

4: If the above three methods are not, it may be a ballast problems, please contact the supplier to solve.

 

Fifth: moving head light is not controlled?

1: check the address code is logarithmic? If the address code on the but not controlled, check the signal line three core has not been reversed? And check whether the connection between the cartoon and the card faucet is in a condition (poor contact);

2: If the address code on the case, the signal line connection is no problem, the address code at the DMX lights will flash normally, if not flash is a connection problem;

3: with the same console to go alone to connect another lamp test, if there is no problem, then prove that the uncontrolled lamp board or display board problems, please contact the supplier to solve.

 

Sixth: shaking his head off the belt?

1: If the light body X / Y axis are not responding, but the console and other lights are normal operation, there may be broken belt;

2: If the X axis does not move, but Y axis movement, or X axis movement, but the Y axis does not move, may be broken belt;

3: If there is more than the above phenomenon, you can turn off the lights in the case of hand toss X / Y move, feel if there is a belt in the drive, if it is very easy to move on the easy, to prove broken belt , Please contact the supplier to solve.

 

Seventh: moving head lights appear out of step?

1: If you move your head out of the image, please rewrite the program and try again.

2: If it is not enough, it proves that a function of the motor or motherboard of an IC burned out, please contact the supplier to solve.

 

The above is our Auban in the after-sales service encountered in the process of some of the most common on the moving head of the problem, we summed up, and we hope to help, if there is more on the stage lighting problems, you can contact us.

1508921178(1).jpg